game rip gratis download Foreign Legion: Multi Massacre

type='html'>

Foreign Legion: Multi Massacre, the far too long awaited follow up to Buckets of Blood. The game is a fun for all (even mac users) multiplayer cartoon-style third-person shooter. With your friends (if you have some

you take the role of a Legionnaire to shred a huge army of non-descriptive cannon fodder to lots and lots of pieces. This kill count is added to the global kill count,that unlocks new content for all players,including mac users

Foreign Legion: Multi Massacre Download

rar: congtruongit.com
add .rar extension then extract

 

Mengukur Kapasitor Menggunkan Multi Meter

type='html'>

Previous cargo in the condenser discharge (connected pin positive and negative). set the multimeter on the stride Ohm, paste investigator red poles on the positive and black on the negative.

When the needle deviate to the right and then a fade back to the left, the condenser means. When the needle does not move, condenser dropping out and when the needle moves to the full right and not back, the possibility of leaking condenser.

Cara mengukur menggunakan Multi meter

Notes:

To test elco 10 F x1k in stride. Capacity for up to 100 F at x100 stride, above 1000 F, x1 stride and test non-electrolyte condenser stride on x10 k.

Mengukur Transistor Menggunakan Multi Meter

type='html'>Ekivalen transistor with two dioda combined, so that the test dioda principle applied to the test transistor.

Cara Mengukur Transistor Menggunakan Multi Meter

Multimeter set on step x100, investigators in the black paste on the base and red at th colector, needle should move to the right. When the investigators moved to Emitor red, needle should move to the right again.

Then the investigators red on the base and black at the Colector, needle should not deviate, and when investigators black moved to Emitor needle also must not deviate.

next Multimeter set on the step 1 k, investigator in the black paste the collectors and red on the emittor, needle must digress a little to the right and if the investigators behind, the needle should not deviate. When one of the events do not happen, then transistor damaged.

For PNP Transitor type, the test is done with the investigators red on the base and black on the colector, needle must digress to the right. Similarly, when the red investigator moved to Emitor, needle must digress to the right again.

Cara Menguji LDR menggunakan Multi Meter

type='html'>

The resistance value of LDR (Light dependent resistor) will change with light intensity about it or around it. In dark conditions the resistance of approximately 200KΩ and LDR in bright Around 500Ω. LDR is made from semiconductor materials such as cadmium sulfide. With this material the energy of the light that falls cause more load to the electric current is released or increased. This means that the material resistance has decreased.

LDR can be easily tested by using a multimeter. because the resistance of an LDR varies according to the light falling on it. At bright light, the LDR resistance will be around 500Ohms and at darkness the resistance will be around 200K. For a proper diagnosis we need to measure the resistance of the LDR at bright light and at darkness.

Gambar Cara Menguji LDR menggunakan Multi Meter

When exposed to light

Keep the multimeter at Ohms mode. The LDR must be subjected to a bright light source (day light is enough).Connect the LDR leads to the multimeter terminals as shown in the figure. Now the multimeter will show a low resistance reading around 500 Ohms.

When dark

Keep the multimeter at Ohms mode. The LDR must be subjected to darkness by covering it with an opaque paper. Connect the LDR leads to the multimeter terminals as shown in the figure. Now the multimeter will show a high resistance reading around 200K.

Menguji Dioda Menggunakan Multi Meter

type='html'> Menguji Dioda Menggunakan Multi Meter

In the diode consists of cathode and anode, and this is given one mark. Then the steps using a multimeter diode test is as follows:

1. Turn the switch on the Ohm, let R x 1K
2. Investigators Attach the red to the cathode (+) and black Investigators at the anode (-) diode
3. If the needle moves multimeter that is good, but if the needle does not move means diodes have been broken or damaged
4. Then a black investigator then attached to the cathode (+) and red pencolok attached to the anode (-). When the needle multimeter silent, means the diode is in good condition but if the move means that the diode has been leaked (damaged)

About Diode

A diode is the basic electronic component. It’s property is that it can conduct only in one direction. A diode can be made by joining a p type semiconductor and an n type semiconductor. At the junction point there will be a voltage drop due to the migration of carriers. The voltage at this barrier is known as barrier potential. Ideally the barrier potential is zero. But in practical case there will be a drop of 0.7 Volts.

When the P side of diode is connected to the positive of power supply and N region is connected to the negative of supply, the diode is said to be in forward biased condition. At this condition, if the applied voltage is greater than the barrier potential of the diode, it starts conduction. After the diode is arrived in the conduction mode, the drop across it remains at 0.7 V. After the conduction starts, if the voltage is increased further, current trough it increases linearly with voltage.

When the supply voltage is reversed the diode is said to be in reverse biased condition. Here there is no conduction at lower voltage values .If we increase the voltage value further ,it is observed that at a voltage the current sharply increases due to the breakdown of the P-N junction. This damages the device.