Showing posts with label volt). Show all posts
Showing posts with label volt). Show all posts

Monday, August 13, 2012

Variable Adaptor ( 3 , 4 , 5, 9, 12 sampai 37 volt)

type='html'>

Variable Adapter (3 , 4 ,5 ,9 ,12 ,16 ,20 to max 37 volt)

The LM117 series of adjustable 3-terminal positive voltage regulators is capable of supplying in excess of 1.5A over a 1.2V to 37V output range. They are exceptionally easy to use and require only two external resistors to set the output voltage. Further, both line and load regulation are better than standard fixed regulators. Also, the LM117 is packaged in standard transistor packages which are easily mounted and handled.

In addition to higher performance than fixed regulators, the LM117 series offers full overload protection available only in IC's. Included on the chip are current limit, thermal overload protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment terminal is disconnected.

Normally, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in which case an input bypass is needed. An optional output capacitor can be added to improve transient response. The adjustment terminal can be bypassed to achieve very high ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators.

Besides replacing fixed regulators, the LM117 is useful in a wide variety of other applications. Since the regulator is “floating” and sees only the input-to-output differential voltage, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not exceeded, i.e., avoid short-circuiting the output.

Also, it makes an especially simple adjustable switching regulator, a programmable output regulator, or by connecting a fixed resistor between the adjustment pin and output, the LM117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current.

For applications requiring greater output current, see LM150 series (3A) and LM138 series (5A) data sheets. For the negative complement, see LM137 series data sheet.

Variable adaptor
Gamabr skema Rangkaian Adaptor Variable 1.2 - 37 Volt

to set the output you can use the formula below. or with a set 5k VR, the output 1.2 volt anad smallest maximal 25 volt



Features Adjustable Regulator LM117/LM317A/LM317
  • Guaranteed 1% output voltage tolerance (LM317A)
  • Guaranteed max. 0.01%/V line regulation (LM317A)
  • Guaranteed max. 0.3% load regulation (LM117)
  • Guaranteed 1.5A output current
  • Adjustable output down to 1.2V
  • Current limit constant with temperature
  • Pa Product Enhancement tested
  • 80 dB ripple rejection
  • Output is short-circuit protected

Table LM117/LM317A/LM317

Friday, August 10, 2012

Rankaian Charge HP Menggunakan battery AA (3 volt)

type='html'>Rankaia Charge hp Menggunakan battery AA (3 volt)
With this tiny thing you can almost charge all the devices which are charged via the USB, like iPod or cellphones, with only two Aa-Cells!

Thus why I should build this?
The reason is completely simple: I am bored empty batteries (IPod, cellphone) while I 'am on the outward journey. And the solution with the linear regulator as 7805 is in fact very
simple, but very unefficient, because: firstly you need a provisioning which provides approximately 3 volts more than you need for the usb and secondly the majority of the cases the difference enters the tension of entry and the tension of output are lost in heat.
The solution to the problem comes from linear technology. Compenent most important of the cicuit presented in the next stages is LT1301 . It is a small stage
to the top of the converter for establishing the mode of commutation actuate the supplys with only some external components.
Rangkaian Charge hp Menggunakan battery AASkema Rangkaian Charge HP Menggunakan battery AA

Rangkaian Charge Spesifikasi:
  • Input: 1,5 to 3 volts
  • Output: 5 Volts @ 200mA max. (really enough to charge an iPod mini or a mobile phone, trust me ;-) )
  • Watts and efficiency:
  • In: 0,95W at 2,5 V
  • Out: 0,875W at 5 V
  • loss: 0,075W
  • 8 percent loss
  • 92% efficiency

The input capacitator should be as close as possible to pin 6 (Vin) of the LT1301!
Keep all cicuit traces short! Directly tie Pin1(GND) Pin8 (PGND) and Pin3 (Shutdown) togheter and connect it to ground. Avoid long soldering times for to prevent destruction of components by overheating... For the detailed placement of the components on the circuit board you can use your own creativity...

So much now its fact, but before connecting it to any device usb, is sure that functions correctly! (the tension should be 5 volts, the LED only would owe rougeoyer, etc) when all ischecked and you are sure that all works you can (if you like it) start to put the hot cast iron around it as a a little protection. If you would put 't as the hot cast iron you can put device in a box of matches or very which you want. left wing of the image you see an older version of the right-sided than you see the smaller and increased version newer